On this page below you can get additional quality additional info in regards to Installing A Bathtub.
Setting up a bathtub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old tub is readily accessible, the task can move immediately; if you have to open up a wall to eliminate the old tub as well as position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. Make sure you have certified on your own for the work and are comfortable attempting it. Instead of hiring a service provider to take control of a halfway-completed project, it is better to think about utilizing one before you start. Possibilities are you might need an expert plumber to make tube connections.
This short article will aid you set up a new bathtub in your washroom if you have already bought a new bathtub as well as don't require to alter the arrangement of your previous supply of water pipes.
Your devices and product list ought to comprise the following:
Planning for the Setup
Firstly, the supporting framework supplied with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its final position.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, activate the taps to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be rather bothersome because of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. When the supply pipelines have been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, put the tub in the needed placement. The wood boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the spirit level reads degree.
To set up taps, fit all-time low of the outermost versatile faucet port to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water system and inspect all joints and brand-new pipework for leakages as well as tighten them if essential. Fill the bathtub and likewise check the overflow electrical outlet and the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the maker's user's manual. Tiling and also sealing around the bathtub needs to wait until the bathtub has been utilized a minimum of once as this will settle it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin making certain that the washing machines are in place between the faucet as well as the sink. Secure the tap in position with the maker offered backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The previous type must be linked to the faucet finishes initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to fracture an inflexible seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, bring about problems with dampness and possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components as well as fittings. They are sold in tubes and cartridges, and also are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to enable the motion experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly offered on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about How to Install a Bathtub? Put feedback down below. We will be delighted to see your insights about this article. We hope that you come back again later on. Are you aware of someone else who is occupied with the topic? Do not hesitate to share it. Thank-you for going through it.
Plumbing care available.